BT-PON

[agenovez]

I have this ONU, it does not reset by pin, or by software, I think it has a bug or something:

I managed to attach a TTL to Serial from an ESP32 ( I didn ´t think it was possible) but shows this:

RTL9602C
PRELOADER Bismarck 3.5
II: PLR:23ce710c, Build_date:20072815, Toolkit:rsdk-4.8.5-5281-EB-3.18-u0.9.33-m32ut-170303_lunapro-171213
II: Disable OCP Timeout Monitor
II: Disable LX Timeout Monitor
II: Enable Triple Synchronizer
II:cg_cpu_clk_init done
II:cg_spif_clk_init done
II: CPU 625MHz (625/1/0), MEM 525MHz, LX 200MHz, SPIF 50MHz
II: NOR SPI-F... A14018/MMIO16-1/ModeC done
AK: DRAM AUTO CALIBRATION
AK: ZQ Calibration Passed
AK: ZQ Calibration Passed
AK: ZQ Calibration Passed
AK: ZQ Calibration Passed
AK: MR0: 0x00100d72
AK: MR1: 0x00110040
AK: MR2: 0x00120000
AK: MR3: 0x00130000
AK: clear dwdqor

AK: Bit/max_r_s/max_r_l/max_w_s/max_w_l    Bit/max_r_s/max_r_l/max_w_s/max_w_l
   [ 0]       0      15       0      1b   [16]       0      17       0      19
   [ 1]       0      15       0      1b   [17]       0      17       0      19
   [ 2]       0      17       0      1b   [18]       0      19       0      19
   [ 3]       0      13       0      1b   [19]       0      15       0      19
   [ 4]       0      15       0      1b   [20]       0      15       0      19
   [ 5]       0      15       0      1b   [21]       0      17       0      19
   [ 6]       0      15       0      19   [22]       0      17       0      19
   [ 7]       0      15       0      1b   [23]       0      17       0      19
   [ 8]       0      15       0      1b   [24]       0      15       0      19
   [ 9]       0      13       0      1d   [25]       0      13       0      1b
   [10]       0      13       0      1b   [26]       0      15       0      1b
   [11]       0      13       0      1d   [27]       0      15       0      1b
   [12]       0      13       0      1d   [28]       0      15       0      1b
   [13]       0      15       0      1b   [29]       0      15       0      19
   [14]       0      15       0      1b   [30]       0      15       0      1b
   [15]       0      15       0      1b   [31]       0      15       0      19
AK: DQ enable delay sync with DQ delay tap.
    0xb80015D0=0x06070707, 0xb80015D4=0x07070707, 0xb80015D8=0x06060607, 0xb80015DC=0x07070706

AK: Disable read after write function

AK: dram auto calibrtaion is done
II: MEM_PROBE_OK
II: MEM_XLAT_OK
II: MEM_TO_REG_OK
II: MEM_CAL_OK
II: Change Stack from 0x9f007ff8 to 0x80efffe0
II: Decompressing U-Boot (0x83c00000 <- 0x9fc17610)... (196 KB <- 72 KB) OK
II: Starting U-boot... 


2011.12.NA_PL..V3.5_R4854_V1.05 (Jul-28-2020 - 15:30:37)

Board: RTL9602C, CPU:625MHz, LX:200MHx, MEM:525MHz, Type:DDR2
DRAM: 128 MB
SPI-F: A14018/MMIO16-1/ModeC 1x16 MB (plr_flash_info @ 83c2fb00)
Loading 8192B env. variables from offset 0x40000
Loading 8192B env. variables from offset 0x42000
Using default environment

Loaded 8192B env. variables from offset 0x42000
Eeprom Read or Write 64K data for test!
[Eeprom1]BSP_EepromRead Eepdata crc check pass.chksum = 0xec59c37e,calc = 0xec59c37e
Eepdata crc check pass.
Can't overwrite "ethaddr"
Net:   LUNA GMAC 
Warning: eth device name has a space!

Test LED By gpioNum(On):29(0) 28(0) 35(0) 26(0) 40(0) 36(0) 
Set PON VCC off, GPIO 43(1)!
Hit any key to stop autoboot:  1 ��� 0 
swcore_init

multicast_start Using LUNA GMAC  device
mcastUpgradeHandler dst ip is 0xffffffff
mcastUpgradeHandler dst ip is 0xffffffff
mcastUpgradeHandler dst ip is 0xffffffff
mcast upgrade timeout.
## Booting kernel from Legacy Image at 83000000 ...
   Image Name:   Linux Kernel Image
   Created:      2020-10-24  15:37:45 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2198902 Bytes = 2.1 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 3.18.24 (root@test-virtual-machine) (gcc version 4.8.5 20150209 (prerelease) (Realtek RSDK-4.8.5p1 Build 2536) ) #11 Sat Oct 24 23:37:34 CST 2020 [luna SDK V3.3.0]
RTL9602C PLL
CPU0 revision is: 0000dc02 (Taroko)
Determined physical RAM map:
 memory: 06eff000 @ 00000000 (usable)
 memory: 00eff000 @ 07000000 (usable)
II: Kernel command line modified: mtdparts=rtk_spi_nor_mtd ->   mtdparts=physmap-flash
Zone ranges:
  Normal   [mem 0x00000000-0x07efefff]
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x00000000-0x06efefff]
  node   0: [mem 0x07000000-0x07efefff]
Initmem setup node 0 [mem 0x00000000-0x07efefff]
icache: 64kB/32B, dcache: 32kB/32B, scache: 0kB/0B
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32000
Kernel command line: console=ttyS0,115200   mtdparts=physmap-flash:512K(boot),512K(config1),512K(config2),2432K(kernel1),4808K(rootfs1),2432K(kernel2)ro,4808K(rootfs2)ro,64K(eeprom1),64K(eeprom2),64K(authrom1),64K(authrom2),56K(cfg1),56K(cfg2),4K@0ro,4K@0ro,4K@0ro,4K@0ro root=/dev/mtdblock6 bootVersion=2011.12.NA_PL..V3.5_R4854_V1.05,Jul-28-2020-15:30:37
root_dev_setup line 301 root: /dev/mtdblock6
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 117024K/129016K available (4895K kernel code, 736K rwdata, 1212K rodata, 188K init, 3690K bss, 11992K reserved)
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 623.41 BogoMIPS (lpj=3117056)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
devtmpfs: initialized
NET: Registered protocol family 16
cpuidle: using governor ladder
cpuidle: using governor menu
SCSI subsystem initialized
set_usbphy(491)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
=================================
CONFIG_LUNA_SOC_GPIO: gpio_init()
=================================
=================================
luna_wdt_init
=================================
************ Watchdog Setting ****************
WDT_E=0, (1-enable, 0-disable)
LX(MHz)=200
WDT_CLK_SC=0
PH1_TO=0
PH2_TO=0
WDT_RESET_MODE=0
**********************************************
=========== SRAM Mapping Init ===============
sramInit: SRAM Mapping begin_addr(804c0000), mapping size(32768) 
=============================================
futex hash table entries: 16 (order: -5, 192 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
ntfs: driver 2.1.31 [Flags: R/W].
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 228
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x18002000 (irq = 49, base_baud = 12327200) is a 16550A
serial8250: ttyS1 at MMIO 0xb8002100 (irq = 50, base_baud = 12327200) is a 16550A
console [ttyS0] disabled
** 23 printk messages dropped ** Kernel command line: console=ttyS0,115200   mtdparts=physmap-flash:512K(boot),512K(config1),512K(config2),2432K(kernel1),4808K(rootfs1),2432K(kernel2)ro,4808K(rootfs2)ro,64K(eeprom1),64K(eeprom2),64K(authrom1),64K(authrom2),56K(cfg1),56K(cfg2),4K@0ro,4K@0ro,4K@0ro,4K@0ro root=/dev/mtdblock6 bootVersion=2011.12.NA_PL..V3.5_R4854_V1.05,Jul-28-2020-15:30:37
root_dev_setup line 301 root: /dev/mtdblock6
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 117024K/129016K available (4895K kernel code, 736K rwdata, 1212K rodata, 188K init, 3690K bss, 11992K reserved)
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 623.41 BogoMIPS (lpj=3117056)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
devtmpfs: initialized
NET: Registered protocol family 16
cpuidle: using governor ladder
cpuidle: using governor menu
SCSI subsystem initialized
set_usbphy(491)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
=================================
CONFIG_LUNA_SOC_GPIO: gpio_init()
=================================
=================================
luna_wdt_init
=================================
************ Watchdog Setting ****************
WDT_E=0, (1-enable, 0-disable)
LX(MHz)=200
WDT_CLK_SC=0
PH1_TO=0
PH2_TO=0
WDT_RESET_MODE=0
**********************************************
=========== SRAM Mapping Init ===============
sramInit: SRAM Mapping begin_addr(804c0000), mapping size(32768) 
=============================================
futex hash table entries: 16 (order: -5, 192 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
ntfs: driver 2.1.31 [Flags: R/W].
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 228
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x18002000 (irq = 49, base_baud = 12327200) is a 16550A
serial8250: ttyS1 at MMIO 0xb8002100 (irq = 50, base_baud = 12327200) is a 16550A
console [ttyS0] disabled
Trying to free nonexistent resource <0000000018002000-000000001800201f>
serial8250.0: ttyS0 at MMIO 0x18002000 (irq = 49, base_baud = 12327200) is a 16550A
console [ttyS0] enabled
SOC_ID 0x6485
unknown bond id
aipc: register chrdev(254,0)
aipc: create device successed
aipc: init done
loop: module loaded
RTL9600 Ethernet driver v1.0.0 (Oct 17, 2015)[Dual Band Disable]
TX[1024,64,64,64,64] , RX[1024,256,256,64,64,64]
eth0: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
eth0.2: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
eth0.3: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
nas0: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
>>>> Set nas0 carrier off !!! 
pon0: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
RTL8686 GMAC Probing..
first entry: 0, portmask 127, rx: 804b5920
priority: 0, portmask 127, rx: 804b5920
insert here, priority: 2, portmask 2047, rx: 801b9dc0
<rtl_rx_special_process_hook_init> register rtl_bgm_rx hook success!

priority: 2, portmask 2047, rx: 801b9dc0
priority: 0, portmask 127, rx: 804b5920
insert here, priority: 1, portmask 2047, rx: 801b9e5c
<rtl_rx_special_process_hook_init> register rtl_enet_rx hook success!

eth0.2 -> 0x1
eth0.3 -> 0x2
Init RTK Driver Module....rtk_switch_irq_init 354 irq=8 name=apl_sw
rtk_gpio_irq_init 523 irq=42 name=apl_gpio
rtk_gpio_irq_init 536 irq=41 name=apl_gpio2
OK
Init RTK Core Dev Module....OK

 rtdrv_init !!! for netfilter
pkt_redirect_init complete
interrupt broadcaster init ok!
PPP generic driver version 2.4.2
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
reigster rtl86xxregister rtl86xx (0) 
rtl86xx-ehci rtl86xx-ehci: Realtek rtl86xx On-Chip EHCI Host Controller
rtl86xx-ehci rtl86xx-ehci: new USB bus registered, assigned bus number 1
rtl86xx-ehci rtl86xx-ehci: irq 14, io mem 0x18021000
rtl86xx-ehci rtl86xx-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
rtl86xx_hcd_cs_init: register rtl86xx_ehci ok!
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
u32 classifier
nf_conntrack version 0.5.0 (1828 buckets, 7312 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
NET: Registered protocol family 10
netlog: listening on port 4660
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Bridge firewalling registered
Ebtables v2.0 registered
8021q: 802.1Q VLAN Support v1.8
physmap platform flash device: 04000000 at 14000000
II: Redirecting 0x1fc00000...
II: Redirection done
Luna SPI NOR FLASH G3 driver-A14018/MMIO16-1/ModeC 
17 cmdlinepart partitions found on MTD device physmap-flash
Creating 17 MTD partitions on "physmap-flash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000100000 : "config1"
0x000000100000-0x000000180000 : "config2"
0x000000180000-0x0000003e0000 : "kernel1"
0x0000003e0000-0x000000892000 : "rootfs1"
0x000000892000-0x000000af2000 : "kernel2"
0x000000af2000-0x000000fa4000 : "rootfs2"
0x000000fa4000-0x000000fb4000 : "eeprom1"
0x000000fb4000-0x000000fc4000 : "eeprom2"
0x000000fc4000-0x000000fd4000 : "authrom1"
0x000000fd4000-0x000000fe4000 : "authrom2"
0x000000fe4000-0x000000ff2000 : "cfg1"
0x000000ff2000-0x000001000000 : "cfg2"
0x000000000000-0x000000001000 : "Partition_013"
0x000000000000-0x000000001000 : "Partition_014"
0x000000000000-0x000000001000 : "Partition_015"
0x000000000000-0x000000001000 : "Partition_016"
Can't request IRQ for timer2

====== RTK PCM Controller Initialization =======
Request IRQ for PCM Controller OK!.
================= FISISH ===============
VoIP control bind 1 (1) instances successfully.
VoIP RX netfilter hook init done!
VoIP RX netfilter hook for IPv6 init done!
ProfileInit
=============RTK VOIP SUITE=============
SDK VoIP Version: VoIP-1.6-DSP-R5523-Luna-R23-rtp refine 
Board CFG Model :  
INITIAL VOIP MANAGER PROGRAM
INITIAL VOIP DSP PROGRAM
IMEM_init_OK
INIT VAR OK
=== RTP Event Send Tasklet Initialization ===
========================================
�[33mAdd RFC2833 TX Timer
�[0m
VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
devtmpfs: mounted
Freeing unused kernel memory: 188K (806b1000 - 806e0000)
random: init urandom read with 2 bits of entropy available

starting pid 39, tty '': '/etc/init.d/rcS'
 #mount rwdir (ont.mib) ok 
# num is 10,nothing need to do
 #mount rwdir2 (ont.mib) ok 
nf_nat_ipsec loaded
nf_conntrack_ipsec loaded
nf_conntrack_l2tp version 3.1 loaded
nf_nat_rtsp v0.7 loading
nf_nat_rtsp loaded
nf_conntrack_rtsp v0.7 loading
nf_conntrack_rtsp loaded
register forward hook for nf_ip_urlfilter_hooks_ops success.
register nf_ip_urlfilter_sockopt_ops success. IPT_SO_SET_MAX:65
nf_conntrack_urlfilter loaded
Try to get Nor Flash MTD authority part configure data.
Use Flash MTD authority part configure data.
misc driver init module 

nvram_init mtd_size 0x2000
misc driver init ok



�[H�[JONT>ssp_CreateApplications 941 [/usr/sbin/aDaemonMgr]

--------start daemon init--------- 
This version support MAC segment:
	60:D2:DD:26:AA:83~60:D2:DD:27:C3:C2
	00:E0:4C:80:00:00~00:E0:4C:90:00:00
	00:00:00:01:00:02~00:00:00:01:00:02
Starting Application: 0x0001f000, /usr/sbin/aDaemonMgr................Done. elapsed time:(1020)ms

ssp_CreateApplications 941 [/usr/sbin/TimerMgr]

Starting Application: 0x00002000, /usr/sbin/TimerMgr................Done. elapsed time:(1020)ms

ssp_CreateApplications 941 [/usr/sbin/LogMgr]

Starting Application: 0x00001000, /usr/sbin/LogMgr................Done. elapsed time:(1020)ms

ssp_CreateApplications 941 [/usr/sbin/MiscMgr]

mmr_XmlInit(): 

Load XML OK from file /mnt/cfgc/cfgc_default.xmlTx has not calibrated!!
Starting Application: 0x00007000, /usr/sbin/MiscMgr................Done. elapsed time:(1020)ms

partId[101], bakPartId[100] 
major ID[0x1312] minor ID[0x1]

ssp_CreateApplications 941 [/usr/sbin/MecMgr]

VOS_XML_Init(): 

Load XML OK from file /mnt/rwdir/runtime_rg.xmlVOS_XML_Init(): 

Load XML OK from file /tmp/default_rg.xmlVOS_XML_Init(): 

Load XML OK from file /tmp/runtime_rg.xmlVOS_XML_Init(): 

Load XML OK from file /tmp/runtime_rg.xmlVOS_XML_Init(): 

Load XML OK from file Starting Application: 0x00003000, /usr/sbin/MecMgr................Done. elapsed time:(1360)ms

ssp_CreateApplications 941 [/usr/sbin/PonMgr]

Starting Application: 0x00004000, /usr/sbin/PonMgr................Done. elapsed time:(1020)ms

ssp_CreateApplications 941 [/usr/sbin/NetMgr]

Starting Application: 0x00009000, /usr/sbin/NetMgr................Done. elapsed time:(1020)ms

ssp_CreateApplications 941 [/tmp/VmrMgr]

ssp_CreateApplications 941 [/usr/sbin/IgmpMgr]

ssp_CreateApplications 941 [/usr/sbin/EthMgr]

Starting Application: 0x00005000, /usr/sbin/EthMgr................Done. elapsed time:(1020)ms

ssp_CreateApplications 941 [/usr/sbin/OamMgr]

/tmp/default_rg.xml
-------- EPON register state INIT or LINK DOWN --------
VOS_XML_Init(): 

Load XML OK from file Starting Application: 0x00014000, /usr/sbin/OamMgr................Done. elapsed time:(1020)ms

ssp_CreateApplications 941 [/usr/sbin/WebMgr]

/tmp/runtime_ver.xmlc524c0:Exit TMR -->mec, msg 0x10001(timeid:0x8),elapsed time:610 ms

Starting Application: 0x0000c000, /usr/sbin/WebMgr................Done. elapsed time:(1030)ms

ssp_CreateApplications 941 [/usr/sbin/CatvMgr]

Starting Application: 0x00018000, /usr/sbin/CatvMgr................Done. elapsed time:(1020)ms

ssp_CreateApplications 941 [/usr/sbin/tr069Mgr]

CfgDIR = /etc/tr069cfg
cd /tmp/cpe3
dir = data
dir = filetrans
dir = options
dir = parameter
cdir = /tmp/cpe3
ifconfig: SIOCSIFMTU: No such device
ifconfig: SIOCSIFMTU: No such device
add call back OK
device lan1 is already a member of a bridge; can't enslave it to bridge br0.
Starting Application: 0x0000d000, /usr/sbin/tr069Mgr................Done. elapsed time:(6880)ms

1481060:Exit SSP -->ssp, msg 0x50000,elapsed time:18470 ms

14b1da0:Exit MEC -->net, msg 0xc0002,elapsed time:6370 ms



INFO: ALL APPs are ready.

Maybe you can recommend me a version for this ONU, because the provider does not answer.

Best regards.